carburizing的例句大全

The Process Design of Controlled Atmosphere Carburization Using Kerosene as a Carburizing Agent

以煤油作渗剂的可控气氛渗碳工艺设计

Study on Rare-earth Deep Carburizing Steel

稀土深层渗碳钢的研究

Improvement of the Multiple Impact Contact Fatigue Resistance of Carburizing Steel

提高渗碳钢多冲接触疲劳抗力的研究

Standard and Development Trend of Carburizing Steel for Automotive Gear

汽车渗碳齿轮钢标准和发展趋势

Study on Low Temperature Gas Multielement Co-penetration on Alloy Carburizing Steel Surface

合金渗碳钢表面低温气体多元共渗研究

Selection of Carburizing Steel for Rolling Mill Bearings and Design of Carburized Layer

轧机轴承渗碳钢的选择和渗碳层的设计

Effect of silicon on microstructure and properties of meta-bainitic carburizing steel were studied.

研究了硅对准贝氏体渗碳钢渗碳组织与性能的影响。

The application of the box type gas carburizing heat treatment line with controllable atmosphere

控制气氛箱式气体渗碳热处理生产线的应用

A newly developed BBH pre-vacuum-pumping carburizing furnace has been introduced in this paper.

介绍了新研制的预抽真空式可控气氛气体渗碳炉。

Aging of Solid Carburizing Agent

固体渗碳剂的老化

Measurement for carburizing layer ′ s depth of quenching and tempering component by metallography

淬回火零件渗碳层深度的金相法测定

The influences of the factors ( casting size, pouring temperature, preheating temperature, graphite sand depth) on the effect of carburizing case depth, carbon concentration gradient have been studied.

研究了铸件尺寸、浇注温度、铸型预热温度、石墨砂层厚度等因素对渗层深度、碳浓度分布等的影响；

Simulation Study on Fluidized Bed Carburizing Layer Depth Mathematic Model

流态化渗碳层深度数学模型仿真研究

Online detecting for carburizing depth of iron and steel parts based on Online LS-SVM

基于Online LS-SVM的钢铁件渗碳层深度在线检测

The article describes the composition and application of a box type gas carburizing heat treatment line with controllable atmosphere.

本文介绍了控制气氛箱式气体渗碳热处理生产线的组成及其应用情况。

Abstract In this paper, we expound the gist of the process control in thick-layer carburizing for heavy-duty gears which includes the selection of the suitable carburizing temperature, cycle and ratio of the carburizing to diffusing period, the way and the demand of carbon-potential control.

阐述了大型重载齿轮深层渗碳工艺控制的要点，包括渗碳温度和时间的合理选择，强渗与扩散时间的最佳分配，碳势控制的途径和要求。

The Application of New Technology to Seal up Box Type Carburizing Furnace Main Construction

新技术在密封箱式渗碳炉主要构件中的应用

The Theoretical Expression of Carbon Potential for Carburizing Atmosphere and Its Exact Measurement

渗碳气氛中碳势理论表达式及精确测定

Processes of Producing Qualified High-Carbon Gray Iron Melt with Cupola Furnace and Analysis on Its Carburizing Mechanism

高炉铁液变质处理初探冲天炉熔炼优质高碳铁液及其增碳机理分析

Test results show that the carbide can be precipitated and grown isothermally from high-temperature austenite on carburization. The formation of massive carbide under ordinary carburizing conditions is the result of accumulative growth and its mean diameter is proportional to the cubic root of time.

试验结果表明，渗碳时碳化物可以直接从高温奥氏体中恒温析出和长大，一般渗破条件下形成的块状碳化物是集聚式长大的结果，其平均半径和时间的1/3次方成正比。