This paper direct independent reinforcement of column against, explore anneal reinforcing bar spiral hoops strengthen technology.

Firstly, equiaxed microstructure could be produced by treatments including hot compression and duplex anneal.

本文首先通过变形及双重退火获得了很好的等轴组织.

The films also can be annealed in air or reductive circumstance according to the requirement.

根据性能的要求也可以选择在空气中或者在还原气氛中退火.

The crystal morphology, microstructure and hydrogen-annealed formation process has distinct impact on the sag resistance.

且钨丝的晶粒形状 、 组织结构、烧氢定形工艺均对其抗下垂性能有明显影响.

We produce the annealed wire with high-quality low carbon raw materials through wire drawing, anneal process.

镀锌铁丝采用中低碳钢盘条为原材料, 按生产工艺可分为热镀铁丝和电镀铁丝.

The CPC electronic packaging materials have the best integrated properties when annealed under the temperate.

研究了不同退火工艺对轧制复合CPC电子封装材料力学性能、物理性能的影响.

The transmittance of the YSO H _ 2-annealed obviously decreases after radiation in the 200-500 nm spectral ranges.

辐照后,氢气退火的样品在200 ～ 500nm波段透过率显著降低.

The measuring results temperature resistance of the sample annealed at 500℃ was indicative of kondo effect.

结果表理,样品的电阻表现为类似近藤效应的现象.

Why shall harden steel be annealed?

'淬火'.''钢为什么要退火 呢 ?

Procedure: annealed, eddy current detection, alignment, rounded, hydrostatic testing, pickling, product inspection.

工艺流程: 退火, 涡流探伤, 矫直, 整圆, 水压试验, 酸洗, 成品检验.

Rough machining and semi-finishing of the material in its soft ( annealed ) condition.

在软 ( 退火 ) 工况下材料的粗加工和半精加工.

An abbreviation for " hot rolled annealed and pickled. "

热轧、退火、酸洗的缩写.

Both tensile strengths decrease when annealed at temperature higher than 920 ℃.

℃以上退火,二者强度都出现降低.

Appreciate those who hurt you, because he annealed your mind.

感激伤害你的人, 因为他磨练了你的心态.

Tool steel is generally purchased in the annealed condition.

工具钢通常是在退火后买卖.

The annealed walls froze all the rigid grief of the actress.

上了釉的墙壁凝冻了这位女演员的一切死板的哀伤.

One two-speed annealing furnace Glassware, Kao Hua furnace, favored by the industry.

其中双速玻璃制品退火炉 、 烤花炉, 深受同行业青睐.

Annealing: Heating to 400 ~650 Holding time 1 ~3 h, Colding in furnace.

退火: 加热至400～650℃,在此温度停留1～3小时, 在炉中冷却.

In addition, this kind of material could be machined after annealing treatment.

且该材质具有退火后可切削加工的性能.

The purpose of annealing the metal is to relieve the stress.

给金属退火是为了减少一些应力.

In the paper, the structure of morden continuous annealing furnace was introduced.

文章介绍了现代用于冷轧不锈带钢生产的连续退火炉的组成及结构.