CALIPER LEDGES ( TO REAR )

Excuse me. I want to use our vernier caliper. the one you borrowed last time!

不好意思. 我想用一下我们的游标卡尺. 就是你上次借用的那一把!

Install caliper over rotor and into mounting bracket.

在转子上方安装夹制器至固定托架中.

Be able to use measure instrument, such as caliper, feeler gage, micrometer and so on.

熟悉使用常用计量器具, 如卡尺, 塞尺, 千分尺等.

I prefer to use these rather than a caliper.

我比较喜欢用这个胜于校准仪(caliper).

Install rotor, caliper, and wheel and tire assembly, then adjust parking brake shoes.

安装转子, 夹制器, 和车轮和轮胎组合, 然后调节手煞车蹄片.

Install brake shoes in caliper.

在夹制器中安装煞车蹄片.

Micron: Alternative term for Micrometre . A unit to denote the caliper of paper and board.

微米: 英文是百万分之一米的另一写法. 表示纸或纸板厚度的单位.

Must be familiar with general measurement technique, such as Caliper, Micrometer and Gauges etc.

熟悉一般测量器具的使用, 如游标卡尺 、 千分尺及螺纹规等.能看懂机械图纸.

The carpenter gauged the dowel with calipers.

那木匠用卡钳估量暗榫.

Use of measuring equipment such as Micrometers, Calipers, Plain Limit Gauges etc is essential.

会使用计量器具,如微米, 卡尺, 平原极限仪表等,是必不可少的.

Brake calipers may be fixed, sliding or floating.

刹车钳可以是固定式, 滑动式,浮动式.

A type of waterproof electronic digital calipers is devised using eddy current displacement sensor.

利用电涡流位移传感器可以研制出防水性电子数显卡尺.

All measurements should be recorded in metric notation, using calipers if clinically assessed.

临床评估用测径器(卡尺)测量,所有测量用米制为单位记录.

He picked up the calipers and measured carefully.

他拿起双脚规仔细测量.

The braking system features 360 mm diameter ventilated discs at the front with four piston calipers.

制动系统采用360毫米直径的通风盘上的前4活塞卡钳.

An accurate and inexpensive method is known as skinfold thickness measures using skinfold calipers.

准确的和便宜的方法因为皮褶厚度用皮褶卡钳措施而出名.

Drive Shafts , Steering Racks , Brake Calipers, Power Steering Pumps, Automotive Parts, Components and Spares.

采购产品传动轴, 转向衣架, 制动器卡钳, 动力转向泵, 汽车零件, 部件和零件.

The rear features 13.8-inch ( 350 mm ) ventilated discs with lightweight aluminum single piston sliding calipers.

后部功能13.8英寸 ( 350毫米 ) 通风碟片轻质铝合金单活塞滑动卡钳.

Figure 5 shows the edge points found after the tool runs the calipers.

图五就是图四的卡钳运行后找到的边缘点.

Experience to use following equipment: balance scale, microscope, torque device, force device, calipers, heat chambers, etc.

有使用下列设备的经验: 天平 、 显微镜 、 扭矩仪 、 拉力计 、 卡尺 、 烘箱, 等.